# Bandit 250XP Used Price & Common Problems | Chipper Risk

> Bandit 250XP: used $2,396 to $46,000. Documented problems: feed-roller shaft coupler and feed roller bearing. OEM part prices and what to inspect before you buy.

**Verdict:** inspect

$2,396–$46,000 observed used. Biggest documented cost risk: the feed roller bearing on the feed-motor side. Buy only after inspection.

**Observed used price:** $2,396–$46,000

**Documented failure risks:**
- Feed roller bearing: Feed roller bearing on the feed-motor side is called out directly as a weak
- Knife/anvil wear reduces chip quality and throughput if not: Knife/anvil wear reduces chip quality and throughput if not serviced -- 
- Anvil: Anvil-side locking nut/ring is safety-critical hardware; specific failure consequences were not documented in the sourced evidence.
- Chipper main bearing: Chipper main bearing (cross-platform Bandit evidence): one owner's original
- Feed-roller shaft coupler: The feed-roller drive uses a loose slip-fit coupler that owners report fatiguing and breaking. Two independent arborist-forum witnesses: the coupler "really ought to be a taper fit on the shaft, or at least keyed. It's neither"; another had the shaft "fatigued off after 19 years." Bandit told an owner they no longer use this system and a different-style repair kit may exist. A dealer quoted the shaft/coupler/pin at ~$544 and feed-roller+shaft/coupler/pin at ~$1,900 (AUD, directional).

## Sources
- [arboristsite.com](https://arboristsite.com/threads/choosing-between-to-bandit-250xp-your-thoughts.255326/) (accessed 2026-08-19)
- [youtube.com](https://www.youtube.com/watch?v=xuCDIzSsq2g) (accessed 2026-08-19)
- [youtube.com](https://www.youtube.com/watch?v=qTihGJPw69U) (accessed 2026-08-19)
- [youtube.com](https://www.youtube.com/watch?v=Jn5AkDC9Gkg) (accessed 2026-08-19)
- [machinio.com](https://www.machinio.com/listings/113682786) (accessed 2026-08-19)
- [machinio.com](https://www.machinio.com/listings/100146014) (accessed 2026-08-19)
- [r.jina.ai](https://r.jina.ai/https://www.machinio.com/bandit/250xp/wood-chippers) (accessed 2026-08-19)
- [Bandit 250XP feed-roller shaft repair: coupler design fault (arborist forum)](https://arboristsite.com/threads/bandit-250xp-feed-roller-shaft-repair.280261/) — "The entire mechanism - stator coupler, shaft and tapered pin pretty much sucks. There's a removable coupler on the stator, and it really ought to be a taper fit on the shaft, or at least keyed. It's neither, the fit from new is kind of loose slip fit." (accessed 2026-09-12)
- [Bandit 250XP feed-wheel hyd-motor connection: shaft fatigued off after 19 years](https://arboristsite.com/threads/bandit-250xp-feed-wheel-hyd-motor-connection.277417/) — "The feed roller shaft is split into fours pieces and one of these pieces has fatigued off after 19 years of use... Bandit did tell me that they don't use this system any longer and there may be a repair kit available of a different style of coupling." (accessed 2026-09-12)
- [OEM anvil 981-0501-01 (fits 250XP & 255XP): $241.40](https://modernequipmentparts.com/981-0501-01-anvil-4-sided-for-250-w-eyebolt-since-1-25-95-see-note/) — "981-0501-01, "Anvil 4-Sided For 250 W/Eyebolt", $241.40 — category "Disc Chippers – 250XP & 255XP"." (accessed 2026-09-12)

_Last verified 2026-09-12. Source: Chipper Risk — https://chipperrisk.com/chippers/bandit-250xp/ — every claim checked against a primary source before publication (see /methodology/)._