Short version: pick the capacity you actually need, then buy on the condition of the feed system, safety devices and knives, not the paint. Earlier versions of this guide cited dealer asking prices, forum repair quotes and failure folklore; we removed them because no official source states them. What remains is sizing advice, inspection questions and safety checks from manufacturers and OSHA.
Size it to the work
Vermeer's product guidance says a good rule of thumb is to purchase a chipper that can handle at least 80 to 90 percent of the tree and brush a contractor intends to chip. It warns about the other direction too: selecting a chipper with greater capacity than necessary will likely impact operational costs like fuel consumption.
Bandit's buyer's guide suggests taking the average size desired to chip and then going up to the next size or two available. Morbark adds that the typical size of the wood you feed your chipper should be about 2/3 of its capacity, with occasional larger pieces. The three makers agree on the idea, even though their rules of thumb differ, so use your real typical material rather than your biggest piece.
Understand what "used" means
Morbark describes three tiers of remanufactured equipment from its own program. Rebuilt means components with less than 50% wear life left are replaced, issues are repaired, and the unit is given a complete clean, paint, and decal service. A refurbished machine has had safety issues inspected/repaired, any obvious needs addressed, and the whole unit is touched up. A basic used machine has safety issues addressed, plus basic servicing as to filters, oils, and knives/tips.
These are Morbark's definitions. A private or auction seller of any brand is not bound by them, so ask exactly what was inspected and replaced.
Inspect with the manufacturers' checklists
Vermeer's buyer's guide checklist includes: Inspect access to the anvil, knives, belts, filters and lubrication points. It also says to confirm local wear-part availability. Bandit's manual explains why knives matter: dull knives make the chipper vibrate excessively, causing machine fatigue, damage, and the engine to use more fuel.
Bandit's manual also says that Bandit Industries, Inc. does not warranty clutch failures, so a worn clutch on a used Bandit is a cost you carry. Ask for service records and look at the clutch under load.
The safety check that is not optional
OSHA reports that the vast majority (78 percent) of the chipper fatalities it counted resulted from being caught in the chipper. Before you talk price, confirm the feed control and emergency stops work. Bandit's manual says to make sure, with everything shut down and stopped, that last chance cables freely operate the feed control valve. Bandit's safety page also describes an engine-disable plug on the hood locking pin: when it is unplugged the engine will not operate. Confirm it is present and working. A machine with a defeated or missing feed-stop control is a liability.
Check recalls and campaigns by serial number
Vermeer filed a wheel campaign bulletin with NHTSA for certain brush chippers. It says owners of the brush chippers identified above were mailed an owner letter notification to inspect the wheels to identify IF it was equipped with supplier defective wheels. Match the seller's serial number against the bulletin, and ask whether the work was done. Other makers publish their own bulletins, so ask each manufacturer or dealer.
What we could not source
No official source gives used chipper prices by size class, so this guide gives none. Treat any figure a seller quotes as unverified until you compare it with a written dealer quote. The two free tests we used to recommend, spinning the feed wheel by hand and loading the feed system, still make sense as common practice, but no official source tells you what a given result costs, so we leave the repair costs out.
Sources
Every quotation above was fetched from the document linked here and matched word for word on 2026-10-27.
- Choosing the right size brush chipper for your fleet and why it matters (Vermeer), checked 2026-10-27
- Choosing the right size brush chipper for your fleet and why it matters (Vermeer), checked 2026-10-27
- Chipper Buyer's Guide (Bandit Industries), checked 2026-10-27
- BVR10 Brush Chipper (Morbark), checked 2026-10-27
- Used & Demo Equipment (Morbark), checked 2026-10-27
- Used & Demo Equipment (Morbark), checked 2026-10-27
- Used & Demo Equipment (Morbark), checked 2026-10-27
- Wood Chipper Buying Guide to Match Your Crew and Workload (Vermeer), checked 2026-10-27
- Wood Chipper Buying Guide to Match Your Crew and Workload (Vermeer), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Commitment to Safety (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Field Campaign Service Bulletin SVC2022-054, BC1000XL wheels (Vermeer Corporation (filed with NHTSA)), checked 2026-10-27
- Hazards of Wood Chippers (SHIB 04-16-2008) (OSHA), checked 2026-10-27