This schedule is built from manufacturer documents, mainly Bandit's Model 75 operating manual, with guidance from Vermeer and Morbark. Earlier versions of this guide promised to double chipper life and cited a 25 hour knife rule, anvil prices and storage tips; we removed those claims because no official source states them. Your own machine's manual always overrides this page.
Before any maintenance
Bandit's manual says: before attempting any type of maintenance, disengage clutch, wait for the disc to come to a complete stop, turn off engine, remove the ignition key, make sure the ignition key is in your possession, install the disc lock pin, and disconnect the battery.
Break-in and daily checks (Bandit Model 75)
- After the first hour on a new machine: Bandit says it is very important after you have operated a new machine for approximately an hour to shut down the machine and recheck all nuts and bolts.
- Bolts: all nuts and bolts should be checked daily, especially the anvil and knife nuts and bolts for torque and fit.
- Hood hinge: lubricate the hood hinge daily.
- Hydraulic oil: the manual says the reservoir level should always remain at 7/8 full and should be checked daily to avoid excessive heat build up.
- Bearings: grease the feedwheel bearings with one shot of an EP-2 Lithium type grease. Vermeer's daily guidance points the same way, with special attention to the two main cutter drum bearings and the feed roller bearings that are in constant motion during operation.
- Radiator: thoroughly clean radiator fins at least once a day or more in excessive conditions.
- End of day: Vermeer says to top off the fuel tank to help prevent condensation buildup.
Weekly, 3 months and yearly (Bandit Model 75)
- Weekly: lubricate pivot points of the feedwheel control bar weekly.
- Hydraulic filter: it must be replaced after first 10 hours of operation, using a 10 micron filter. After the first change replace the oil filter every 3 months or 400 hours.
- Suction screen: change hydraulic suction screen(s) yearly or every 2000 hours.
- Fuel tank: drain and clean the fuel tank yearly.
Knives: different makers, different numbers
Knife intervals vary, and the makers do not agree on one number:
- Vermeer says typically, knives should be checked at 10-hour intervals, and that knife maintenance intervals are heavily influenced by the type of wood being chipped and the chipping conditions.
- Vermeer also gives a rule of thumb to replace the knives after 50 hours of use, with earlier replacement if they become dull.
- Morbark's TW 160PH page says knives should be sharpened after every 25 hours of use.
- Bandit's manual says knife mounting hardware must be replaced after maximum of 4-5 knife rotations/changes to ensure safe clamping ability.
The reason to keep to the schedule is stated by Bandit: operating your chipper with dull knives increases the amount of power required to chip, increases machine vibration and cause feeding problems.
Belts and long-interval items
Vermeer says the drum drive belt on the BC1000XL should be replaced every 500 hours, or more often if it shows signs of damage or wear. It adds that dealers can help monitor the hours on the machine and communicate with the customer on what should be replaced at 100 hours, 250 hours and 1,000 hours. Vermeer does not publish that item list in the article we fetched, so ask your dealer.
What we left out
No official source we fetched gives oil-change intervals for all chippers, a storage routine, fluid analysis advice, anvil prices or a figure for how much maintenance extends life. Follow the engine maker's manual for engine service and your chipper manual for the rest.
Sources
Every quotation above was fetched from the document linked here and matched word for word on 2026-10-27.
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Brush Chipper and Stump Grinder Maintenance Guidelines (Vermeer), checked 2026-10-27
- Brush Chipper and Stump Grinder Maintenance Guidelines (Vermeer), checked 2026-10-27
- Discover How Sharp Brush Chipper Knives Maximize Chip Quality (Vermeer), checked 2026-10-27
- TW 160PH Brush Chipper (Morbark), checked 2026-10-27
- TW 160PH Brush Chipper (Morbark), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Brush Chipper and Stump Grinder Maintenance Guidelines (Vermeer), checked 2026-10-27
- Brush Chipper and Stump Grinder Maintenance Guidelines (Vermeer), checked 2026-10-27
- Daily Brush Chipper Maintenance to Perform on Vermeer AX17 (Vermeer), checked 2026-10-27
- Daily Brush Chipper Maintenance to Perform on Vermeer AX17 (Vermeer), checked 2026-10-27