Vermeer SmartFeed
Vermeer's page for the BC1000XL describes SmartFeed as a patented feed-sensing control system that boosts operator productivity and reduces engine strain by monitoring engine rpm and controlling feed rollers. The BC700XL sheet says its SmartFeed control system helps increase operator productivity and reduces strain on vital engine parts, as engine rpm is monitored and feed rollers are controlled.
The BC1500 sheet gives the most detail:
The SmartFeed system monitors engine rpm and automatically stops and reverses the feed rollers to enhance production. This system also senses feed roller jams and manipulates the material automatically to reduce the need for manual control bar use.
Vermeer now calls this system SmartFeed. Older articles and forum posts may use the name AutoFeed for similar controls, so confirm what a particular used machine has.
Bandit auto feed
Bandit lists a control panel with reversing auto feed as a feature of its hand-fed chippers, and offers an optional autofeed feature on some. Its manual gives one setting to check:
If your chipper is equipped with the optional autofeed feature, make sure it is set correctly. The setting for the low R.P.M. stop must be high enough not to allow the chipper discharge to plug.
The same manual explains plugging more broadly: operating the engine at speeds lower than full R.P.M.'s causes your chipper to plug, and dull chipper knives also contribute to chipper plugging.
What a manual control bar does
Not every chipper has electronic feed sensing. OSHA describes the mechanical feed control bar, where pushing the feed control bar to the center (neutral position) stops the feed rollers, and pushing it toward the discharge spout reverses the feed rollers. Feed sensing is an addition to this control, not a replacement for the safety devices.
What this means when you inspect a used machine
These points are our suggestions based on the sources. Ask which feed control the machine has, and test it under load according to the manual. If the feed hesitates, check the knives and engine speed first, given Bandit's plugging guidance. Do not accept an unexplained workaround: Bandit's safety page says never to operate equipment that is in need of repair.
We have no official source for failure rates or repair costs of feed-sensing electronics, so we give none. Ask the manufacturer or a dealer for a written quote and the service history of the specific machine.
How this guide changed
Earlier versions of this guide were built on a forum story about a drifted pickup sensor, a damaged control board and a repair bill; we removed it because no official source states those figures or that case. This version covers what the manufacturers say their feed-sensing systems do and what settings and conditions they link to feeding trouble.
Sources
Every quotation above was fetched from the document linked here and matched word for word on 2026-10-27.
- Vermeer BC1000XL Brush Chipper with Gas Engine (Vermeer), checked 2026-10-27
- Vermeer BC1000XL Brush Chipper with Gas Engine (Vermeer), checked 2026-10-27
- BC700XL Brush Chipper spec sheet (02/25) (Vermeer), checked 2026-10-27
- BC700XL Brush Chipper spec sheet (02/25) (Vermeer), checked 2026-10-27
- BC1500 Brush Chipper spec sheet (04/26) (Vermeer), checked 2026-10-27
- BC1500 Brush Chipper spec sheet (04/26) (Vermeer), checked 2026-10-27
- 250XP - Towable (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Hazards of Wood Chippers (SHIB 04-16-2008) (OSHA), checked 2026-10-27
- Commitment to Safety (Bandit Industries), checked 2026-10-27