Two systems, two jobs
Bandit's 250XP page describes the feed side: dual feed wheels driven via 32.3 CID hydraulic motors providing 4,480 pounds of pulling power. The cutting side on many machines is engaged through a clutch or belt drive. So the question is not clutch or hydraulic, but which of the two systems is worn on the machine you are looking at.
The clutch side
- Adjustment. Bandit says that if not adjusted correctly, the clutch will slip under a load causing feeding problems.
- Service. Its manual says to check for proper lubrication and engagement tension adjustment, and to frequently adjust and lubricate per the PTO clutch manufacturer's manual.
- Use. The manual's rule: do not use the clutch to dislodge a jam.
- Warranty. Bandit states that it does not warranty clutch failures, so the cost of a worn clutch on a used Bandit falls on the owner.
- Bearing hazard. The manual warns that a clutch can self engage if either the pilot or throw-out bearing happens to seize to the main output shaft.
Clutch alternatives from other makers
Vermeer's BC1000XL page describes a clutchless PTO system that helps prevent premature wear on the belt drive by only allowing engagement at low idle. Its BC700XL sheet describes a manual clutch whose engagement transfers belt tension from the disk to the engine smoothly to help prevent premature wear, and its BC1500 sheet lists an automotive-style clutch as the engagement system. Morbark describes a ZeroClutch on its BVR line, whose integrated drum speed sensor monitors the drum speed and prevents the clutch from engaging if material becomes stuck between the feed wheel and drum.
So on a used machine, identify which engagement system it has before comparing its condition with another machine.
The hydraulic side
- Oil level. Bandit says the reservoir should always remain at 7/8 full and be checked daily to avoid excessive heat build up.
- Filter. The manual says the filter must be replaced after the first 10 hours of operation with a 10 micron filter, then every 3 months or 400 hours.
- Cleanliness. Vermeer says that if you add hydraulic fluid, pass it through a 10-micron filter before adding it to the tank.
- Leaks. Bandit warns that high pressure oil can easily puncture skin, causing serious injury or death, so never check for leaks with fingers.
What we could not source
No official source gives repair times, repair costs or a ranking of which system is more expensive to fix. Those claims from the earlier version are removed. Get written dealer quotes for whichever system you suspect.
How this guide changed
Earlier versions of this guide were built on video teardowns of two Bandit machines, plus repair timing claims; we removed them because no official source states them. This version sticks to what the manufacturers publish about the two systems, which are usually different parts of the same machine.
Sources
Every quotation above was fetched from the document linked here and matched word for word on 2026-10-27.
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Vermeer BC1000XL Brush Chipper with Gas Engine (Vermeer), checked 2026-10-27
- 250XP - Towable (Bandit Industries), checked 2026-10-27
- Vermeer BC1000XL Brush Chipper with Gas Engine (Vermeer), checked 2026-10-27
- BC700XL Brush Chipper spec sheet (02/25) (Vermeer), checked 2026-10-27
- BC1500 Brush Chipper spec sheet (04/26) (Vermeer), checked 2026-10-27
- BC700XL Brush Chipper spec sheet (02/25) (Vermeer), checked 2026-10-27
- BC1500 Brush Chipper spec sheet (04/26) (Vermeer), checked 2026-10-27
- BVR10 Brush Chipper (Morbark), checked 2026-10-27
- 250XP - Towable (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Model 75 Operating and Parts Manual (1/21) (Bandit Industries), checked 2026-10-27
- Daily Brush Chipper Maintenance to Perform on Vermeer AX17 (Vermeer), checked 2026-10-27
- Commitment to Safety (Bandit Industries), checked 2026-10-27